1 hp 115 V 750W AC industrial servo motor & Driver 10 NM torque 300-4,500 RPM

  

1 HP 750 Watt Computer Controlled Servo Motor. New 2023 design with external rotary speed control.

Note: See image 2 and 3. Rotary switch upgraded with more accurate display, improved pot, different style knob and access to install stop/start switch.. Image shows most common left side entry.

This Face Mount Version comes with M6 X 1.0 stainless button head mounting screws. If you prefer flush fit, ask about ordering it machined to fit M6 - 1.0 flush fit screws before you order. Speed is programmable for any range between 300 to 4,000 RPM See images for measurements. Note: the maximum distance between control unit and motor is 30 inches. Runs on typical 110 to 120 volt AC household power supply's.

A complete servo motor as seen in images. A stand alone and programmable custom built servo motor driver with thermal overload protection. A custom built external rotary speed control switch assembly as seen in images. One 750 watt (1 HP) servo motor. One external rotary speed control switch.

You will not be able to dissemble the speed control switch so tell me if you plan to change it. Tests with the 750 watt motor. Switch have revealed as follows.

The new custom made high performance pots are here and installed in the 750's. This pot is not only much better quality, it also has 20% more rotation.

For this reason the original. Positions displayed on the sticker will not match. Position on switch 300 on display 300.

Position on switch 600 on display 800. Position on switch 1,000 on display 1,300. Position on switch 2,000 on display 1,700. Position on switch 3,000 on display 2,200. Position on switch 4,500 on display 3,000. 4,500 rpm is all the way past at 5:30. This will require a different label to match but there is no reason to run a print. Due to the fact we have lots more testing to do with all motors and control units. Motor programming + spindle speeds and Reverse.

The motor speed can be programmed to operate in any range chosen by the user. Between 300 and 4,500 RPM's.

The full range of speed (RPM's) can also be controlled with just the speed control knob. Only requires a few easy steps. Reverse is simple, just hold the yellow button for a few seconds.

Includes the ability to set bottom and top RPM range separately. In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below). Slowest speed achievable: Motor 400 RPM. Highest speed: 4,500 RPM. Soft start is programmable and will be set as soft as possible when you receive this motor. This program is very effective in reducing drive belt wear etc. Braking strength is also programmable and will be set as low as possible. Personally I wish I could set it lower. Safe turn on system where the speed control knob must be in the full counter clockwise (stop) position when turned on. When turned on the self. System checks for faults and will not allow the motor to turn on until the speed control knob is turned all the way to stop first. Use at your own risk.

Watt: 750 (1.0057665666 HP). RPM: 3 00 to 4,500 RPM in 100 RPM increments. This listing is for what is seen in the primary image.

It will include printed programming instructions. Large flat rate box and to USA only. This item will be in strict. Applied to this item when it was listed. See details, what's covered and for how long etc below.

If found to be abuse or missing the. Or demos that I have from previous builds. Additionally original packaging such as Styrofoam package inserts must be used to return these parts. Note: Cutting too much material will result in a jam.

This may damage the main board. Timing belt and small parts are not covered. Customer alterations and machine work are not covered and may. Please contact me As long as there is no abuse, I will offer a solution. This often includes parts at cost and free installation.

Yes, I keep control boards in stock for this reason. I also keep motors, belts and every part used to build these in stock. Just contact me and we will have you up and running within days, not 6 months waiting for parts from China. Ask lots of questions before ordering: Especially about intended use.

That way we can advise if this motor is a good fit. Do not worry about missing this item.

If you miss it, I will build more within a day or two.